The AUDIENT iD1 audio interface is a desktop USB-C sound card for anyone recording vocals, guitar and instruments to a computer in a home studio, or making podcasts and streaming. It has 2 inputs and 2 outputs, an Audient Console preamp with 75 dB of clean gain and 32 bit conversion up to 192 kHz.
Audient Console preamp. It uses the same fully analog design as the flagship ASP8024-HE console and delivers 75 dB of clean gain, enough to drive an SM7B or any dynamic microphone without a booster. The Class A circuit keeps the signal clean even on whispered vocals. With Smartgain you play the loudest part and the iD1 sets the level in a few seconds, without clipping and with optimized headroom.
Analogue Tone Suite and ORBIT. They act on the preamp before the signal reaches the DAW. HMX is a discrete MOSFET circuit that adds body, LIFT opens up the high frequencies of dull vocals, and GLOW blends them together. ORBIT is the relay-controlled variable impedance control, which changes the interaction between preamp and microphone: PUNCH 2.8 kOhm, SMOOTH 1.2 kOhm, VINTAGE 220 Ohm.
DSP, RoomTune and monitoring. EQ, compression and reverb run on the hardware, with zero latency and no CPU load. RoomTune Monitor Correction is built in, with guided setup in under twenty minutes, and it works in the DAW, in Spotify and across the whole operating system. A stereo monitor output for studio monitors, two headphone outputs of 6.3 mm and 3.5 mm with no adapter, and the Direct Monitor button for near-zero latency tracking, with the main encoder balancing input and playback.
JFET input and iD Control. The JFET instrument input, modeled on the input stage of a classic tube amplifier, gives amp simulators a signal that also suits re-amping; you can record microphone and instrument together, for example vocals and guitar in a single take. With iD Control you manage gain, Tone Suite, DSP FX, routing and monitoring, with Total Recall, Mute, Dim, Mono, polarity inversion, audio loopback and a standalone mode that keeps the settings on the hardware. Metal chassis, clicking encoder, backlit indicators and switches.
| Connections | USB-C |
|---|---|
| Power | USB-C bus power |
| Inputs | 2: 1 Audient Console microphone preamp, 1 JFET instrument input |
| Outputs | 2 line outputs, 1 dual headphone output (6.3 mm and 3.5 mm) |
| Conversion | 32 bit |
| Sample rates | 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz |
| Microphone input | Gain 0 to 75 dB; max level 12 dBu; THD+N at 0 dBu -99 dB (0.0011%); SNR 101 dB (A-weighted); EIN -128 dB (A-weighted); response ±0.1 dB from 10 Hz to 80 kHz; CMRR >70 dB; crosstalk <120 dB; impedance 3 kOhm |
| Line input | Gain -10 to 65 dB; max level 22 dBu; THD+N at 10 dBu -98 dB (0.0012%); impedance 10 kOhm |
| DI input | Gain 0 to 75 dB; max level 12 dBu; THD+N at 0 dBu -70 dB (0.03%); SNR 96 dB (A-weighted); response ±0.5 dB from 10 Hz to 40 kHz; impedance 500 kOhm |
| Phantom power | +48 V DC, 10 mA per channel |
| ADC input | 12 dBu = 0 dBFS; THD+N at -1 dBFS -110 dB (0.0003%); dynamic range 121 dB (A-weighted); response ±0.5 dB from 10 Hz to Fs/2 (Nyquist); crosstalk <120 dB |
| Line outputs | Max level 18 dBu = 0 dBFS; THD+N at -1 dBFS -115 dB (0.00017%); dynamic range 128 dB (A-weighted); response ±0.5 dB from 10 Hz to Fs/2 (Nyquist); impedance 470 Ohm |
| Headphone outputs | Max level 15 dBu = 0 dBFS; THD+N at -6 dBFS -111 dB (0.0003%); dynamic range 125 dB (A-weighted); response ±0.5 dB from 10 Hz to Fs/2 (Nyquist); impedance 2 Ohm |
| Headphone power | Into 30 Ohm 3.7 V peak, 456 mW; into 60 Ohm 5.1 V peak, 434 mW; into 600 Ohm 6.2 V peak, 43 mW |
| DAW mixer roundtrip latency (ADC->host->DAC, 64 sample buffer) | 44.1 kHz 6.500 ms; 48 kHz 6.141 ms; 88.2 kHz 4.38 ms; 96 kHz 4.266 ms; 176.4 kHz 3.266 ms; 192 kHz 3.083 ms |
| Internal mixer latency (ADC->DAC) | 44.1 kHz 0.536 ms; 48 kHz 0.495 ms; 88.2 kHz 0.302 ms; 96 kHz 0.276 ms; 176.4 kHz 0.109 ms; 192 kHz 0.104 ms |
| Measurements | According to the AES-17 standard; tolerance ±1 dB unless otherwise stated |
| Dimensions | 6.3 x 14.3 x 12 cm |
| Weight | 0.497 kg |
The manufacturer reserves the right to change product specifications without notice.
Gain ranges from 0 to 75 dB, with 75 dB of clean gain: enough to drive an SM7B or any dynamic microphone without a booster.
Through USB-C bus power. A 1 m USB C-C cable is included in the box.
Yes, you need the RM1 Reference Microphone. Each RM1 has a factory calibration that RoomTune loads during setup.
Gain, Tone Suite and routing are managed from the iD Control software.
Windows and macOS.